Raoult’s Law Vapour Pressure Calculator

What sits above a mixture, and why it is not what sits in it

Raoult’s law says each component of an ideal liquid mixture contributes vapour in proportion to its mole fraction: pA = xAP*A. Add the partial pressures and you have the total. Set one of them to zero and the same law becomes the vapour-pressure lowering caused by a non-volatile solute, which is where boiling-point elevation comes from. This page draws both components and the total against composition, computes what the vapour is made of, and sketches the shapes real mixtures take when they refuse to be ideal.

Total vapour pressure above the mixture

P = xA P*A + xB P*B
The second case is the first one with P*B set to zero, and it is the one most exam questions are about: sugar or salt in water, where the solute has no measurable vapour pressure of its own. Choosing it blanks the second pure vapour pressure below and makes the total line in the picture fall on top of the solvent’s.
A is the first liquid, or the solvent. Mole fraction, not mass fraction: moles of A divided by total moles of everything in the liquid. The mole fraction of B is whatever is left over, 1 − xA, so you only ever type one of them. Getting a mass ratio into a mole ratio is where most of the arithmetic in these questions actually lives.
The vapour pressure of A on its own, at the temperature of the question. It is strongly temperature-dependent — water goes from 2.34 kPa at 20 °C to 101.325 kPa at 100 °C — so a vapour pressure without a temperature attached to it means nothing. The default pair, 10.0 and 2.9 kPa, is benzene and toluene at about 20 °C, the textbook example of a nearly ideal mixture.
Ignored when the box above says the solute is non-volatile, because then it is zero by definition. Whichever liquid has the higher pure vapour pressure is the more volatile one, and it is the one the vapour will be richer in. That enrichment is the entire basis of fractional distillation.
This adds a dashed curve to the diagram showing the shape a deviating mixture takes. It is a sketch, not a calculation — nothing on this page computes activity coefficients, and the dashed curve is not derived from your numbers. It is there so you can recognise the two shapes, which is what the exam question asks for.
Vapour pressure against the mole fraction of A. The two straight lines are each component's partial pressure, p = xP*, rising from zero at the end where that component is absent; the third straight line above them is their sum. The marker is your composition. Choosing a non-volatile solute flattens B's line onto the axis and the total falls onto A's. The dashed curve, if you asked for it, is a SKETCH of a deviating mixture's shape and is not computed from your numbers.
7.8700kPaExample

benzene and toluene at about 20 °C, with pure vapour pressures 10.0 and 2.90 kPa, in a liquid that is 0.700 benzene by mole

Advertisement

One law per component, then add them

pA = xA P*A  ·  pB = xB P*B  ·  P = pA + pB  ·  yA = pA / P  ·  (P*A − P)/P*A = xsolute
x
a mole fraction in the liquid: moles of that component divided by total moles in the liquid. The two mole fractions add to 1, so one number fixes the composition of a binary mixture
y
a mole fraction in the vapour, which is a different number from x and the single most useful thing on this page. Dalton’s law gives it: the vapour’s composition is the ratio of the partial pressures, so the vapour is always richer in whichever component is more volatile
P*
the vapour pressure of that component pure, at the temperature of the question, marked with a star. These are the two numbers you look up; everything else follows from them and the composition
Raoult
the law itself: p = xP*. It is exact for an ideal mixture, where A–B interactions are indistinguishable from A–A and B–B, and it is exact for the solvent of any mixture in the limit of great dilution. Everything in between is a deviation
Henry
the law that takes over for the solute in a dilute mixture, p = KHx, where KH is a measured constant that is not the solute’s own vapour pressure. The two laws are the two ends of the same diagram: Raoult’s line is the tangent at x = 1, Henry’s is the tangent at x = 0, and for an ideal mixture they are the same line

Worked example

benzene and toluene at about 20 °C, with pure vapour pressures 10.0 and 2.90 kPa, in a liquid that is 0.700 benzene by mole
THE OTHER MOLE FRACTION. xtoluene = 1 − 0.700 = 0.300. In a binary mixture you only ever type one.
EACH PARTIAL PRESSURE SEPARATELY. pbenzene = 0.700 × 10.0 = 7.00 kPa. ptoluene = 0.300 × 2.90 = 0.87 kPa.
ADD THEM. P = 7.00 + 0.87 = 7.87 kPa. Dalton's law: the total pressure of a gas mixture is the sum of what each component would exert alone in the same volume.
NOW THE PART THAT IS ACTUALLY ASKED. What is the VAPOUR made of? ybenzene = 7.00 / 7.87 = 0.8895. The liquid is 70% benzene; the vapour above it is 89% benzene. The vapour is richer in the more volatile component, by a factor of 0.8895/0.700 = 1.271.
WHY THAT FACTOR IS WHAT IT IS. The relative volatility is P*A/P*B = 10.0/2.90 = 3.45, and the vapour-to-liquid ratio follows from it: y/(1−y) = 3.45 × x/(1−x), so 0.8895/0.1105 = 8.05 = 3.45 × 0.700/0.300 = 8.05. One distillation step multiplies the ratio of the two by the relative volatility, every time.
THE SAME SUM WITH A NON-VOLATILE SOLUTE. Set P*B = 0 and P = 0.700 × 10.0 = 7.00 kPa. The relative lowering is (10.0 − 7.00)/10.0 = 0.300, which is exactly the solute's mole fraction. No constant, no fitting — that equality is the whole of the colligative claim.
Advertisement

Vapour pressure of pure water, and what it does to a boiling point

TemperatureP* of waterP above a 0.95 mole-fraction solutionLowering
20 °C2.34 kPa2.223 kPa0.117 kPa
40 °C7.38 kPa7.011 kPa0.369 kPa
60 °C19.93 kPa18.934 kPa0.997 kPa
80 °C47.37 kPa45.002 kPa2.369 kPa
100 °C101.33 kPa96.264 kPa5.067 kPa
105 °C120.8 kPa114.76 kPa6.04 kPa
Pure-water vapour pressures are the conventional steam-table values rounded to the figures shown; the last two columns are computed from them on this page’s own expressions with xwater = 0.95 and a non-volatile solute. Read the last row: at 100 °C the solution’s vapour pressure is only 96.3 kPa, below one atmosphere, so it is not yet boiling — you have to go to about 105 °C before it reaches 101.325. That is boiling-point elevation, arrived at from the vapour pressure rather than from Kb, and it is the same phenomenon.

Ideal, and the two ways to be non-ideal

BehaviourExample pairWhyΔH of mixingΔV of mixingAzeotrope
Nearly idealbenzene + toluene; n-hexane + n-heptaneThe two molecules are so alike that an A next to a B is indistinguishable from an A next to an Aabout zeroabout zeronone
Positive deviationethanol + water; acetone + carbon disulphideA–B attraction is weaker than A–A and B–B, so molecules escape more easily from the mixtureendothermic, absorbs heatexpands slightlyminimum-boiling, if the deviation is large enough. Ethanol and water make one at 95.6% ethanol by mass
Negative deviationacetone + chloroform; nitric acid + waterA–B attraction is stronger — here a hydrogen bond that exists only in the mixture — so escape is harderexothermic, gives out heatcontracts slightlymaximum-boiling, if the deviation is large enough. Nitric acid and water make one at 68% acid
The enthalpy and volume columns are the standard qualitative signatures taught alongside the pressure curve, and they are worth memorising together: positive deviation, endothermic, expands; negative deviation, exothermic, contracts. This page computes only the ideal case. The dashed curve the third input adds is a sketch of the shape, not a model of either pair.

An ideal mixture, a non-volatile solute, and the shapes real liquids take

Raoult’s law is the simplest possible statement about a liquid mixture: if 70% of the molecules at the surface are benzene, then 70% of the escaping-and-returning traffic that sets the equilibrium vapour pressure is benzene traffic, so benzene contributes 70% of the vapour pressure it would have on its own. Each component obeys its own copy of the law, and the total is the sum. That is the whole model, and it is exactly right when an A molecule cannot tell whether its neighbour is an A or a B.

The first thing worth taking from this page is that the vapour and the liquid are different mixtures. The liquid in the worked example is 70% benzene; the vapour above it is 89% benzene. There is nothing exotic about this — the more volatile component simply contributes more than its share — but it is the basis of every distillation ever performed. Condense that vapour and boil it again and it goes to 97%. Each step multiplies the ratio of the two components by the relative volatility, so the separation you can achieve depends on how many stages you can stack, which is what the trays or the packing in a column are.

The second thing is what happens when one component has no vapour pressure of its own. Then P = xsolventP*, the total falls linearly as solute is added, and the relative lowering (P* − P)/P* comes out exactly equal to the mole fraction of the solute. That is the cleanest colligative relationship in the subject: a measurable ratio equal to a particle count with no empirical constant in between, which is why it was the first method used to find molar masses and why it appears in every syllabus. It also explains boiling-point elevation without any new physics: a liquid boils when its vapour pressure reaches the surrounding pressure, and if the solute has flattened the vapour pressure curve downwards, the curve has to be carried to a higher temperature before it reaches one atmosphere.

Real mixtures deviate, and the deviations come in exactly two varieties, which is why they are worth learning as a pair. A positive deviation means the measured total pressure lies above Raoult’s straight line: A and B attract one another less than they attract their own kind, so molecules escape the mixture more easily than they escape either pure liquid. Ethanol and water do this, because mixing them breaks hydrogen bonds between like molecules. Mixing absorbs heat and the volume expands slightly. A negative deviation is the mirror image: A and B attract each other more strongly, escape is harder, the pressure falls below the line, mixing gives out heat and the volume contracts. Acetone and chloroform do this, held together by a hydrogen bond that exists only in the mixture.

Push either deviation far enough and the pressure curve develops a turning point, and at that composition the liquid and the vapour have the same composition. That is an azeotrope, and it is the point at which distillation stops working, because boiling no longer changes what is left behind. Ethanol and water form a minimum-boiling azeotrope at 95.6% ethanol by mass, which is the reason laboratory ethanol comes at that strength and why anything stronger needs a different technique altogether. This page does not compute azeotropes — it has no model of the deviation, only Raoult’s straight line — and the dashed curve the third input draws is a sketch of the shape, put there so you can recognise it, and nothing more.

One more honest limit. Raoult’s law is written for the component present in large excess. For the dilute component, Henry’s law p = KHx takes over, with a constant that has to be measured and is not the solute’s own vapour pressure. On the composition diagram the two laws are the two tangents, one at each end; for an ideal mixture they coincide, and the further a mixture is from ideal the further apart they lie. If the quantity you want is the pressure of a gas itself rather than the vapour above a liquid, the ideal gas equation lives on the ideal gas equation page in the physics plugin, which is a different page and a different calculation.

Frequently asked questions

Why is the vapour richer in the more volatile component?

Because each component contributes vapour in proportion to both its mole fraction and its own pure vapour pressure, and the composition of the vapour is the ratio of those contributions. If A is three and a half times as volatile as B, then at equal mole fractions it contributes three and a half times as much vapour. Written as a ratio it is tidy: yA/yB = (P*A/P*B) × (xA/xB). The factor in the brackets is the relative volatility, and one distillation step multiplies the ratio by it.

Is relative lowering of vapour pressure really a colligative property?

Yes, and it is the most direct of the four. With a non-volatile solute, (P* − P)/P* = xsolute exactly, with no constant of proportionality to look up — unlike Kf, Kb or RT. Nothing about the solute enters beyond how many particles it supplies, which is the definition of colligative. In dilute solution xsolute ≈ nsolute/nsolvent, and that form is what molar-mass questions use.

What exactly makes a mixture ideal?

That the A–B interaction is the same strength as the average of the A–A and B–B interactions. Then a molecule’s escaping tendency does not depend on who its neighbours are, and the only thing that matters is how many of each kind there are. In practice this needs two liquids that are chemically and structurally alike: benzene with toluene, hexane with heptane, bromoethane with chloroethane. The giveaways that a mixture is not ideal are that it warms or cools on mixing and that the volumes do not add.

Why does ethanol stop at 95.6%?

Because ethanol and water deviate positively from Raoult’s law strongly enough that the total vapour pressure curve has a maximum, and at that composition the vapour has the same composition as the liquid. Boiling it therefore does not enrich anything, and no number of distillation stages gets past it. That mixture boils at 78.1 °C, below the boiling point of either pure component, which is what “minimum-boiling azeotrope” means. Going beyond it needs something other than simple distillation — a third component, a molecular sieve, or a pressure change, since an azeotrope’s composition moves with pressure.

Can I use mass per cent instead of mole fraction?

Not directly. Raoult’s law counts molecules, so you must convert: divide each mass by its molar mass to get moles, then divide by the total. For benzene (78.11) and toluene (92.14) the two are close enough that mass per cent gets you within a couple of per cent, which is exactly the kind of near-miss that makes the mistake hard to spot. For water and sucrose they differ enormously: 10% sucrose by mass is a mole fraction of only 0.0058.

Related calculators

References

  1. Chemistry, Textbook for Class XII, Part I, Unit “Solutions”, National Council of Educational Research and Training, New Delhi. The table of molal elevation and depression constants used on this page was read on 14 November 2026 from NCERT’s own e-text of that unit at ciet.nic.in/moocspdf/Chemistry03/lech_10204_eText.pdf, which prints, for water, a boiling point of 373.15 K with Kb = 0.52 and a freezing point of 273.0 K with Kf = 1.86 K kg mol−1, and defines the van ’t Hoff factor as the ratio of the number of particles after dissociation or association to the number before it.
  2. P. Atkins, J. de Paula and J. Keeler, Atkins’ Physical Chemistry, Oxford University Press. The standard undergraduate treatment of colligative properties, of the van der Waals equation and of the compressibility factor, including the derivation of the critical constants from a and b and the definition of the Boyle temperature. Cited from the printed text; no online copy was fetched.
  3. Chemistry, Textbook for Class XII, Part I, Unit “Solutions”, NCERT, sections on Raoult’s law for a solution of volatile liquids, on the relation between Raoult’s law and Henry’s law, and on ideal and non-ideal solutions and azeotropes. Read on 14 November 2026 from the same NCERT e-text as above. The qualitative signatures of positive and negative deviation quoted in the second table — the sign of the enthalpy and volume of mixing, and the kind of azeotrope each produces — follow that treatment.