Electrolysis and Faraday’s Laws Calculator

Electrolysis and Faraday's Laws Calculator

Current times time is charge; charge divided by the Faraday constant is moles of electrons; moles of electrons divided by the ionic charge is moles of metal. That chain is the whole of Faraday’s two laws, and this page walks it in order, deposits the metal on the cathode in the diagram and bubbles the gas off the anode, both to the numbers you type.

Mass deposited, from current and time

Q = It, then n(e⁻) = Q/F, then m = (Q/F)(M/z)
An ampere is a coulomb per second, which is the only fact you need to turn a current into a charge. A school electrolysis runs at a fraction of an amp to a few amps; an industrial aluminium cell runs at over 300000 A, which is why the upper limit here is generous.
Minutes, because that is how exam questions are worded. The page converts to seconds for you, which is the conversion most often dropped: 30 minutes is 1800 seconds, and forgetting the 60 makes the answer sixty times too small.
Molar masses are the IUPAC abridged standard atomic weights rounded to two decimals. Choosing an entry fills the two boxes below and locks them; choose the last option to type your own.
The molar mass of the element deposited, not of the salt it came from. Depositing copper from copper sulfate uses 63.55, not 159.6.
How many electrons each ion needs. This is the number that makes aluminium expensive: three electrons per atom and a low molar mass, so a mole of charge deposits only 9.0 g of it against 107.9 g of silver.
The same charge passes through both electrodes, so the anode product is fixed by the same number of electrons. Oxygen takes four per molecule and chlorine two, which is why the same cell gives you twice as many moles of chlorine as of oxygen. The third option is the electroplating case, where the anode is made of the plating metal and simply dissolves.
One electrolytic cell, drawn to your numbers. The copper-coloured layer on the cathode is the metal you are depositing: its thickness follows the mass, up to a cap of 90 pixels so that it cannot swallow the beaker. The bubbles on the anode grow with the volume of gas and a new one appears each time the volume passes a threshold, so you can watch four appear as you raise the current. Choose the electroplating option and the bubbles vanish altogether, because in that case nothing is evolved — the anode dissolves instead.
1.4820gExample

A copper sulfate solution electrolysed with inert electrodes at 2.5 A for 30 minutes. Copper deposits at the cathode from Cu²⁺; oxygen is given off at the anode.

Advertisement

Three steps, always in this order

Q = It  ·  n(e−) = Q / F  ·  n(element) = n(e−) / z  ·  m = n(element) × M  ·  so m = ItM / zF
Q = It
amperes times SECONDS. A time given in minutes or hours has to be converted first, and that conversion is the commonest single error on this topic — a factor of 60 or 3600 is hard to spot in an answer that otherwise looks sensible
F = 96485.33212 C/mol
the charge on one mole of electrons, and exact in the present SI. Cambridge 9701 asks you to know it as F = Le, the Avogadro constant times the elementary charge. Most questions accept 96500
z
the charge on the ion, so the number of electrons each ion needs. Cu²⁺ takes two, Ag⁺ takes one, Al³⁺ takes three. It divides, so a higher charge means less metal for the same current
M / z, the equivalent mass
the mass deposited by one mole of electrons. Faraday’s second law is exactly the statement that, for a fixed charge, masses are in the ratio of these numbers — which is how the whole idea of equivalents entered chemistry
the same charge goes through both electrodes
they are in series, so the electrons that arrive at the cathode are the ones that left the anode. That is why one number for Q fixes the product at both ends, and why the gas volume on this page is tied to the metal mass

Worked example

A copper sulfate solution electrolysed with inert electrodes at 2.5 A for 30 minutes. Copper deposits at the cathode from Cu²⁺; oxygen is given off at the anode.
SECONDS FIRST. 30 minutes is 30 × 60 = 1800 s. Write this down before anything else; it is the step that gets skipped.
CHARGE. Q = It = 2.5 × 1800 = 4500 C. Notice that only the product matters: 5 A for 15 minutes would give exactly the same 4500 C and exactly the same answer.
MOLES OF ELECTRONS. 4500 / 96485.33212 = 0.046639 mol of electrons. With the rounded 96500 you get 0.046632 — a difference in the fifth figure, which no exam will care about.
MOLES OF COPPER. Cu2+ + 2e− → Cu, so each atom needs two electrons: 0.046639 / 2 = 0.023320 mol of copper.
GRAMS. 0.023320 × 63.55 = 1.4820 g. Equivalently, straight down the line: m = ItM/zF = 4500 × 63.55 / (2 × 96485.33212).
AND THE GAS AT THE OTHER END. Oxygen takes four electrons per molecule: 2H2O → O2 + 4H+ + 4e−. So 0.046639 / 4 = 0.011660 mol of O2, which at 273.15 K and 100 kPa is 0.011660 × 22.711 = 0.2648 L, about a quarter of a litre. Run the same charge through brine instead and the chlorine takes two electrons rather than four, so you get twice as many moles of gas.
THE CHECK WORTH DOING. Divide the mass by the moles of electrons: 1.4820 / 0.046639 = 31.78 g per mole of electrons, which is 63.55/2, the equivalent mass of copper. If that ratio does not come out as M/z, you have divided by z in the wrong place.
Advertisement

What one mole of electrons — 96485 C, one faraday — deposits

Ion dischargedzM / g mol⁻¹Mass per faraday / g
Ag+1107.87107.87
Cu2+263.5531.78
Zn2+265.3832.69
Ni2+258.6929.35
Al3+326.988.99
Au3+3196.9765.66
Na+ (molten NaCl)122.9922.99
The last column is Faraday’s second law written out: it is simply M divided by z, and it is the mass one mole of electrons will deposit whatever the current and whatever the time. Silver’s figure is the largest in the table, which is why the silver coulometer was for decades the standard way of measuring a quantity of electricity — the mass is big enough to weigh accurately. Aluminium’s is the smallest, and that single number is most of the reason recycling aluminium saves about 95 per cent of the energy of making it. Molar masses are the IUPAC abridged standard atomic weights rounded to two decimals; the last column is computed from them rather than quoted.

Charge is the currency, and the Faraday constant is the exchange rate

Electrolysis questions are counting problems wearing an electrical disguise. The only physics in them is Q = It: a current of one ampere is one coulomb per second, so amperes times seconds is coulombs. Everything after that is stoichiometry. One mole of electrons carries 96485.33212 C — that is the Faraday constant, and in the present SI it is an exact number because it is the Avogadro constant multiplied by the elementary charge, both of which are now fixed by definition. Divide your charge by it and you have moles of electrons, which is a chemical amount like any other and can be put straight into a balanced half-equation.

Faraday’s first law says only the product It matters. Double the current and halve the time and you deposit exactly the same mass. This is worth testing on the calculator above, because it is the quickest way to convince yourself that charge, not current, is the quantity doing the work. It also explains a standard exam trick: a question that gives you two different currents for two different times is asking you to add the charges, not to average anything.

Faraday’s second law is the division by z. For the same charge, the masses of different elements come out in the ratio of their equivalent masses, M/z. A mole of electrons deposits 107.87 g of silver, because each silver ion needs one electron, but only 31.78 g of copper, because each copper ion needs two, and a mere 8.99 g of aluminium, because each aluminium ion needs three and aluminium is light to begin with. That last figure is not a curiosity. It is why aluminium was once more valuable than gold, why smelters are built beside hydroelectric dams, and why recycling the metal saves most of the energy of making it.

Both electrodes carry the same charge, so one calculation fixes both products. The cell is a series circuit: every electron that arrives at the cathode left the anode. So if 4500 C deposits 0.0233 mol of copper at one end, the same 4500 C must produce 0.0117 mol of oxygen at the other, because oxygen needs four electrons per molecule. Change the anode product to chlorine, which needs two, and the moles of gas double while the copper does not move at all. The diagram above shows both ends responding to the one number.

The electroplating case is the one where nothing bubbles. Choose the third anode option and the anode is made of the plating metal: it dissolves at exactly the rate the cathode gains, the electrolyte’s concentration stays put, and no gas appears. That is how electroplating and electrorefining are actually done, and it is why a copper refinery can run for months on the same tank of solution. The gas rows go blank because there is no gas, which is a different thing from a failed calculation.

What this page assumes, and where real cells depart from it. It assumes every electron goes into the reaction you chose — a current efficiency of 100 per cent — and no real cell manages that. Hydrogen comes off alongside the metal if the solution gets dilute or the current density gets high; some charge goes into warming the electrolyte; a competing ion takes a share. Industrial figures are quoted with an efficiency precisely because the theoretical maximum is the easy part. The page also cannot read a chemical formula, so the cathode product is a list of selections plus a box for your own numbers, and it cannot balance a half-equation or work out z for you. For the potential you need to make electrolysis happen at all, see the cell EMF page and the feasibility interpreter; for the charge-and-energy relations of a circuit, physics owns drift velocity and current density.

Frequently asked questions

What exactly is a faraday?

The charge on one mole of electrons: 96485.33212 C, written F. One faraday deposits one mole of a singly charged ion, half a mole of a doubly charged one, and so on. Since the 2019 redefinition of the SI it is an exact number, because F = NAe and both of those are now fixed.

Can I just use 96500?

Almost always, yes. It is 96485.33212 rounded to three significant figures and the difference appears in the fifth figure of an answer. This page uses the exact value so that the rounding is yours to choose rather than built in.

Why do I need the time in seconds?

Because an ampere is defined as one coulomb per second. A time in minutes gives a charge sixty times too small, and the resulting mass looks perfectly plausible, which is what makes it such a reliable way to lose marks. The page converts for you and prints the charge so you can check it.

Why does aluminium give so much less metal than silver for the same charge?

Two reasons multiplying together. Each Al3+ needs three electrons against silver’s one, and aluminium’s molar mass is 26.98 against silver’s 107.87. One mole of electrons therefore gives 8.99 g of aluminium and 107.87 g of silver — a factor of twelve.

How do I get the volume of gas from the charge?

Work out the moles of electrons, divide by the electrons per molecule (four for O2, two for Cl2 or H2) and multiply by the molar volume. This page gives 22.711 L/mol at 273.15 K and 100 kPa, and 24.790 L/mol at 298.15 K and 100 kPa. Check which pair of conditions your board calls STP, because the older 22.4 L/mol figure belongs to 1 atm rather than 100 kPa.

Will I really get this mass in the lab?

No, you will get a bit less. The calculation is the theoretical maximum, assuming every electron does the job you intended. In practice some current goes into evolving hydrogen, into side reactions and into heat, so a real cell is quoted with a current efficiency below 100 per cent. A school experiment that comes within a few per cent is doing well.

Related calculators

References

  1. Chemistry, Subject Code 043, Classes XI and XII (2026 to 2027), senior secondary curriculum, Central Board of Secondary Education, cbseacademic.nic.in (read 14 November 2026). Unit 2 of the Class XII course is Electrochemistry, carrying 9 of the 70 theory marks, and its topic list reads in full: “Electrochemical Cells, Galvanic Cells, Nernst Equation, Conductance of Electrolytic solutions, Electrolytic Cells and Electrolysis, Batteries, Fuel Cells, Corrosion.” What is not named there is worth as much as what is: the words Kohlrausch and Faraday appear nowhere in the Class XII unit text, although both are taught inside “Conductance of Electrolytic solutions” and “Electrolytic Cells and Electrolysis”. Quoted to establish what is in scope, not to claim any endorsement by the board.
  2. Cambridge International AS and A Level Chemistry 9701, syllabus for examination in 2025, 2026 and 2027, Cambridge Assessment International Education, cambridgeinternational.org (read 14 November 2026). Topic 24.2 asks candidates to “calculate a standard cell potential by combining two standard electrode potentials” and to “deduce the polarity of each electrode”, and Topic 24.1 asks for “the relationship F = Le between the Faraday constant, F, the Avogadro constant, L, and the charge on the electron, e” and for “the quantity of charge passed during electrolysis, using Q = It”. Two things in that syllabus are worth flagging because they make an identical question look different on two papers. It writes the Nernst equation as “E = E° + (0.059/z) log [oxidised species]/[reduced species]” — a PLUS sign, the ratio the other way up from the reaction quotient, and z where most Indian textbooks write n. And the phrase “cathode minus anode” does not appear in it at all; the subtraction is left as “combining” two potentials.
  3. CODATA Recommended Values of the Fundamental Physical Constants: 2022, NIST SP 961 (May 2024), physics.nist.gov/cuu/pdf/wall_2022.pdf (read 14 November 2026). The chart gives the Faraday constant as F = 96485.33212 C/mol and the molar gas constant as R = 8.314462618 J/(mol K), in both cases with no uncertainty quoted, because the value is exact: since the 2019 redefinition of the SI the Avogadro constant and the elementary charge are fixed numbers, so F = N(A) e and R = N(A) k are fixed too. Every constant on this page is that value, not a rounded one — the rounding happens only in the 0.0592 shortcut, which is discussed in its own right.
  4. Chemistry, Textbook for Class XII, Part I, National Council of Educational Research and Training, New Delhi — the Electrochemistry unit, which is where the standard-electrode-potential table, the Nernst equation, Faraday’s two laws of electrolysis and Kohlrausch’s law of independent migration of ions are set out for this syllabus. Cited bibliographically only: this source could not be read. ncert.nic.in serves its textbook PDFs under a robots policy that disallows automated retrieval, so nothing on this page is quoted from the chapter and no page or table number is claimed for it.